How Much Does Pressure Washing Cost in Arizona? (2026 Guide)

Across the United States, most residential flatwork (driveways, walkways, patios) is priced somewhere around $0.15 to $0.75 per square foot in 2026, depending on the condition of the surface and the method used. Arizona tends to sit at or slightly below the national middle for basic concrete cleaning, mostly because our driveways are large, flat and do not grow the heavy moss and mildew common in wetter states.

As a rough guide, here is what most Arizona homeowners can expect to see: a standard two-car concrete driveway typically falls in the $80 to $250 range; a back patio or pool deck often lands between $100 and $300; a full single-story house exterior usually runs a few hundred dollars and can climb past $500 for larger two-story homes; and paver cleaning with re-sanding or sealing is a separate, higher-priced job because it involves more steps and materials.

Treat these as market ranges, not quotes. Two homes on the same street in Gilbert or Queen Creek can get very different prices if one driveway has years of oil stains and the other was cleaned last spring.

Most pressure washing companies use one of three models. The first is per square foot, which is common for driveways, patios and commercial flatwork. The contractor measures the area and multiplies by a rate that reflects the surface and how dirty it is.

The second is a flat rate per item, such as a set price for a two-car driveway or a single-story home. This is easy to understand and is popular with residential customers. The third is an hourly or minimum-charge model, where there is a base trip fee and small jobs are rounded up to that minimum. That is why a tiny walkway can cost almost as much as a small patio: the setup, water, fuel and travel time are about the same.

Many companies also offer bundles. Cleaning the driveway, sidewalk, entry and back patio in one visit usually costs less per square foot than booking each area separately, because the crew is already set up on site.

Stain type matters most. General dust and dirt rinse off quickly. Oil and transmission fluid drips, rust from sprinklers or patio furniture, tire marks and hard water rings need pre-treatment with specific cleaners and more dwell time, and that adds labor.

Surface material is the next factor. Plain broom-finish concrete is the most straightforward. Pavers, travertine, flagstone and stamped or stained concrete need lower pressure, more care around joints, and often a different approach to avoid etching or blowing out joint sand. Stucco and painted surfaces on a house usually call for a gentler wash as well.

Access and height also count. Two-story walls, steep slopes, tight side yards and areas without a nearby water spigot take longer. Finally, add-ons like sealing pavers, re-sanding joints, cleaning gutters or treating efflorescence are priced separately from the wash itself.

Regular maintenance is the biggest money saver. A driveway that gets cleaned once or twice a year never builds the deep, baked-in staining that requires heavy chemical treatment. Booking several areas at once, or teaming up with a neighbor so the crew can do two homes on one trip, can also help in many cases.

Clearing the area before the crew arrives saves time too. Move cars, trash bins, potted plants and patio furniture, and let the company know about any sprinkler heads or low-voltage lighting near the surfaces being cleaned.

Our climate creates problems homeowners in other states rarely deal with. Hard water from many East Valley systems leaves white mineral rings on concrete and pavers. Monsoon storms push red mud and debris across driveways and into paver joints. The intense sun bakes oil stains deeper into porous concrete, making older drips harder to lift.

Many HOAs in San Tan Valley, Queen Creek and Chandler also send notices for stained driveways and dirty entries. When a deadline is involved, it is worth asking for a quote early, especially in late summer after monsoon season, when demand tends to rise.

A rented pressure washer usually costs less up front, but it comes with a learning curve. Too much pressure or the wrong nozzle can etch concrete, leave visible stripes, strip paint, or damage pavers and stucco. Homeowners also need to buy the right detergents and degreasers, and a full driveway with a consumer machine can take most of a weekend.

Professional equipment combines higher flow, surface cleaners that leave an even finish, and proper chemistry for oil, rust and minerals. For a large driveway, a full house exterior, or anything with pavers, most homeowners find the time saved and the cleaner result worth the difference.

The fastest way to a real number is to share a few photos and the rough size of each area. Mention the stains you are most worried about, the surface type, and whether you want sealing or only cleaning. A good contractor will explain what is included and what is not.

Splash N StyLin offers free estimates for homes across San Tan Valley and the East Valley. Call or text (520) 371-8081 with a couple of photos and we will tell you exactly what your job involves.